Center Consoles

Center-console boats, builder conversations, and real Arid Bilge Systems installations.

23 10, 2025
  • Midnight Express and Arid Bilge Systems interview thumbnail with Eric Glaser and Alfred Baurley.

Midnight Express: Eric Glaser on Arid Pickup Locations

By |2026-10-13T16:59:44+00:00October 23, 2025|Articles, Blog, Boat Builders, Boat Stories, Center Consoles, Performance Boats|

Where does the water remain after the bilge pump stops? On a boat with several separate compartments, that question needs more than one answer. Arid supplies Midnight Express, and Eric Glaser’s conversation with Alfred Baurley explains how the builder approaches collection points below deck.

Midnight Express builds performance center consoles in Miami and emphasizes customization. The interview brings that idea into an area an owner may see only through an access hatch: the placement of a central drying unit and the lines serving it.

Start with the compartments

Glaser describes mounting the central unit in the rear bilge, with pickups in the rear and mid-bilge. Depending on the customer’s needs, he says, a collection point may also be fitted near the bow thruster where water can remain.

At the time of the interview, Glaser described Arid as an option offered across the builder’s models. The conversation does not identify one particular Midnight Express model, and a buyer should confirm the equipment and pickup plan for the boat being ordered. The useful detail is the approach: choose collection points for the spaces that need them.

Make the pickup plan easy to follow

When reviewing a build or an existing installation, ask for a simple compartment map. Mark the central unit, each pickup and the access point used to inspect it. If the bow-thruster compartment is included, identify its line rather than assuming it is covered because a system is fitted elsewhere.

Then consider service access. Can someone reach the pickup to inspect it? Can the tubing route be followed without moving unrelated equipment? A short walkthrough with the installer can turn an equipment list into something the owner and service team can use.

The Phenom 34 walkthrough offers another example of why separate bilge areas deserve individual attention. The Hylas H57 conversation adds another consideration: where operating equipment sits in relation to the living space. Both are useful comparisons, rather than specifications for a Midnight Express.

See the water-routing animation

Illustrative Arid water-routing animation. Actual equipment placement and pickup locations vary by vessel and installation.

This silent animation shows pickups in separate low areas connected by tubing to a central Arid unit, with collected water moving through a discharge line.

Keep the jobs of the two systems clear

Arid addresses residual water through pickups connected to a central unit. Conventional bilge pumps retain their own job, and a new source of water still needs investigation. Our guide to how Arid works shows the collection and discharge process.

For the owner, the takeaway from Glaser’s account is concrete: understand which compartments are served, how to reach the equipment and what was specified for this boat. Those details belong in the handover as much as the controls at the helm.

For a brief introduction, watch the Midnight Express interview Short.

The Midnight Express interview

Alfred: Eric, can you tell me a little about your experience—how the Arid Bilge System has worked across your Midnight Express boats?

Eric: Yeah, absolutely. We offer Arid Bilge Systems across all of our models. It helps keep the bilges dry and clean, so you’re not worried about all the corrosion and the mess you’d normally find down there. It’s a great option. You guys have a bunch of different versions—some different power supply options—and it works for us depending on which way we’re powering the boat.

Alfred: Where is the system mounted on the boat?

Eric: We mount them in the rear bilge of the boat on every model.

Alfred: What locations does it vacuum from?

Eric: So we do one in the rear bilge, one in the mid-bilge, and then depending on what the customer asks for, sometimes we do one up by a bow thruster, where it might catch a little bit of water—just to help keep everything dry in those areas too.

Alfred: And this has improved your boats by keeping everything nice and dry versus having a wet, moldy environment—especially when you think about protecting your Seakeeper, your generator, and all the sensitive components that are down in those compartments.

Eric: Of course. It’s all good things. Water messes everything up, and we’re in a wet environment on a boat—so it just makes sense to dry it out.

Alfred: Eric, I really appreciate your time.

Eric: No problem. Thanks for making a great product. Keep it up.

Why builders choose Arid: explore the benefits for builders and owners, and read our boat-building story.

22 10, 2025
  • Everglades Boats and Arid Bilge Systems interview thumbnail with before-and-after bilge photographs.

Everglades Boats and Arid: Aboard the 395

By |2026-10-13T16:59:44+00:00October 22, 2025|Articles, Blog, Boat Builders, Boat Stories, Center Consoles|

Arid supplies Everglades Boats. A conversation aboard the 395 puts that relationship in practical terms: what happens in the bilge while a boat is being used, and how does that affect the spaces around its equipment?

In the interview published with our 2025 story, David Brown speaks as Everglades’ Vice President of Product Development and Engineering. He describes Arid as standard equipment on the 395 at that time. Captain Sean Hickey, speaking as a regional manager and company captain, brings an extended-trip perspective to the discussion.

A captain’s account from an extended trip

Hickey recalls roughly 2,500 miles over three months and reports finding the bilge dry when the boat came out of the water. He connects the condition of that space with the generators, stabilization equipment and other systems carried below deck.

That is his account of a particular trip. For another owner, it suggests a useful habit: make the condition of accessible bilge spaces part of regular checks, including after a trip. Record where water returns, and have its source investigated instead of assuming the same result on every boat.

The 395 combines fishing equipment with cabin systems

Everglades’ current 395CC description shows why access matters. The builder lists a finished hull liner, oversized rigging troughs and a cabin-floor bilge hatch. Its equipment list also includes conventional bilge pumps and a high-water alarm.

Arid’s contribution is residual-water collection at connected pickup locations. The conventional pumps and alarm retain their jobs. Brown’s interview explains the fitment described then; confirm the equipment specification for a new build or a different model year with Everglades.

A separate Everglades installation in our archive

Our original archive photographs show another Everglades: a blue-hulled center console with four outboards, paired with its installed Series 2 cabinet. They are not presented as photographs of the 395 interview boat. Our original installation feature keeps those two views together.

Blue-hulled Everglades center console with four outboards underway near a breakwater.
An Everglades center console featured in Arid’s installation archive.
Arid Series 2 cabinet installed among hoses and wiring aboard an Everglades center console.
Arid Series 2 installed aboard an Everglades center console.

Plan for coverage and future access

The cabinet photograph shows one part of the installation. Planning also needs to identify the separate areas where residual water collects and the route between those pickups and the unit. Bring photographs of the low points and access hatches to that discussion.

See how Arid collects residual water, then compare the service-access discussion in HCB’s Estrella interview and the attention to finished equipment spaces in our Bahama Boat Works story. The layouts differ; planning around the actual boat is the common starting point.

A shorter cut of the Everglades interview is also available.

See the water-routing animation

Illustrative Arid water-routing animation. Actual equipment placement and pickup locations vary by vessel and installation.

This silent animation shows pickups in separate low areas connected by tubing to a central Arid unit, with collected water moving through a discharge line.

The Everglades Boats interview

Alfred: Here to go and talk about the Arid Bilge System on the 395, and how the Arid Bilge System makes the Everglades a better boating dry experience. Here to talk about it with David.

David: Yeah, thanks for being here. You’re on the 395. I’m David Brown, the Vice President of Product Development and Engineering. We partnered with Arid Bilge Systems, and it is now a standard feature on this boat. It really helps keep all of the below deck bilges nice and bone dry.

David: It’s been a huge customer satisfaction item—especially for people who keep their boats in the water. Everglades has been building center consoles for years. We offer a full range of boats from our 245 up to our 455, packed full of technology and patented features. So, we’re really proud to be a partner here with Arid Bilge Systems.

Sean: Hi, I’m Captain Sean Hickey with Everglades Boats. I’m one of their regional managers as well as the captain of the company. At Everglades, our philosophy is using nothing but the best parts we can find on the marketplace.

Sean: The last trip I did was a long trip—over about 2,500 miles over the course of three months. We pulled the boat out of the water at the end of that, and there wasn’t a drop of water in the bilge. And that’s imperative these days with Helm Master systems down there—Seakeepers, generators, you name it.

Sean: The Arid Bilge System delivers as promised. It keeps your bilge dry and keeps your electronics safe.

Why builders choose Arid: explore the benefits for builders and owners, and read our boat-building story.

25 06, 2025
  • HCB Yachts and Arid Bilge Systems interview thumbnail with before-and-after bilge photographs.

HCB Yachts and Arid Bilge: Dalton Teeter Interview

By |2026-10-13T16:59:44+00:00June 25, 2025|Articles, Blog, Boat Builders, Boat Stories, Center Consoles|

Arid supplies HCB Yachts. Aboard the 65-foot Estrella, Dalton Teeter explains the relationship through the work people do below deck: inspecting equipment, keeping compartments in good condition and reaching the drying system for maintenance.

The boat provides a distinctive setting for that discussion. HCB’s official Estrella description lists a 65-foot length, a 16-foot beam and a walk-in machine room. The space devoted to onboard systems makes their accessibility a meaningful part of the ownership experience.

Three areas aboard the interview boat

In the interview published with our 2025 story, Teeter describes bilge-drying coverage in the aft bilge, at midship and beneath the master stateroom. He connects those separate areas to the layout of the boat, rather than describing the bilge as one uninterrupted space.

Those are the areas he identifies aboard that Estrella. They are not a universal pickup count or an installation plan for every HCB. When discussing another boat, establish which compartments drain together and which have their own low points before choosing coverage.

Service access belongs in the installation plan

Teeter repeatedly returns to serviceability. He discusses reaching the system and cleaning it after debris enters the pickup arrangement. His account describes the installation he knows; the maintenance procedure for another system should come from its own instructions.

For a buyer or captain, the useful questions are specific. Can someone reach the cabinet connections? Are the pickups accessible for inspection? Will another piece of equipment block those routes later? A walkthrough of the actual spaces is more informative than selecting equipment from the yacht’s length alone.

A separate installation from the HydraSports archive

A separate HydraSports installation feature pairs the four-outboard boat underway with a photograph of its Arid Series 2 cabinet among the equipment. They show another arrangement, not the Estrella discussed in the interview. See the original photographs together in our HydraSports post.

HydraSports center console with four outboards underway, viewed from above.
HydraSports center console from Arid’s installation photo feature.
Arid Series 2 cabinet fitted beside hoses, wiring and other equipment in a HydraSports center console.
Arid Series 2 installed aboard a HydraSports center console.

Put bilge drying in the wider care routine

Arid removes residual water from connected pickup locations. It complements conventional bilge pumps; recurring water still needs investigation. The system overview explains the collection process behind those locations.

For a captain’s longer-trip perspective, continue with Everglades’ 395 interview. Bahama Boat Works’ discussion of fit and finish approaches the same equipment spaces from an owner’s first inspection. Together, the stories show different reasons to include bilge condition and maintenance access in the conversation with a builder.

See the water-routing animation

Illustrative Arid water-routing animation. Actual equipment placement and pickup locations vary by vessel and installation.

This silent animation shows pickups in separate low areas connected by tubing to a central Arid unit, with collected water moving through a discharge line.

HCB Yachts: the Estrella interview

Alfred: Hello, I’m Alfred Baurley here with Arid Bilge Systems, with Dalton at the HCB booth, and he’s going to tell us a little about the Arid Bilge System, his personal experience, and how the Arid Bilge System coexists with his line of boats.

When you take a look at these boats—these HCB boats—they build exquisite boats. They’re massive in size, and they are superbly fast. They have on this boat, Estrella, so much customization. Here at HCB, the customer will have the best boating experience possible.

At Arid Bilge Systems, we keep that boating experience dry, fresh, and clean—just like when it came out of the factory. That’s the point of the Arid Bilge System. That gyro, that generator, all these expensive marine technologies down in your bilges—all that stuff is being kept fresh and clean, as opposed to getting rust and corrosion buildup. No more mold, no more odor.

Dalton, tell me a little about your experience and what you all do here at HCB.

Dalton: First off, welcome aboard the 65′ Estrella, a center console yacht, which is truly amazing. You’re talking about the cockpit area, how wide she is. This is a 16-foot beam, which is massive. I’ve had customers put 14-foot jet boats in here as tenders.

Alfred: I mean, you’ve got a lot of poles too, I can see.

Dalton: Yeah, so funny enough, this one is a 65-foot vessel, top speed of 65, has 65 rod holders, and of course—six 600s. The ‘65 Estrella launched in 2018, and it really launched HCB into the yachting industry. We rebranded into HCB Center Console Yachts in 2018 because of this Estrella, and it put us in a new league. And to be honest, we have rocked that league, I believe.

Alfred: So would you say that the Arid Bilge System really improved your overall quality of boats?

Dalton: Yes. So the dry bilge system—we will not build a vessel without it. It’s too important for the bilge to be dry to not have it in the boat. Having a dry bilge is very important to make sure you’re not only keeping things maintained well, serviced well, and overall cleanliness.

So honestly, on the HCB, which is a high-end center console—it’s a luxury center console, right? We have to have the best of the best, our nature of the beast. We always think, we try to over-engineer things. So the Arid Bilge, for us, is a dry bilge.

A dry bilge is a happy bilge.

We have three sea chests actually in this 65, meaning fewer thru-hulls in the bottom of the boat. Everything’s going into the centralized tank system and feeding it throughout the whole vessel. So, very minimal areas to leak, but if something does get water into the bilge, that dry bilge that you all offer us keeps it a nice, dry bilge.

And it is, like you stated, in three areas: it is in the aft bilge, midship, and right underneath the master stateroom as well—just to keep everyone happy and clean. Honestly, most of the work’s always in the aft bilge pads, and it’s worked really well for us.

Alfred: Would you say that what the Arid Bilge System does—it stops the rust buildup on things like your generator and your gyro?

Dalton: It helps overall maintenance of the vessel—serviceability, things of that nature. You’re keeping the condensation out of the bilge, which is immensely important here in the marine industry. You’ve got a captain, you’ve got someone servicing your vessel—they’re really going to appreciate a dry bilge area.

If I can keep that moisture out of there, I’m going to have less service problems, as well as an overall nicer bilge area.

Alfred: Would you say that it’s a really durable system?

Dalton: I love the serviceability of the system, honestly. It’s easy to work on. It’s easy to clean. You just literally undo the hose, do some air—clean out your hoses if you’ve sucked in some dirt or debris. Because it is more of a pad on the bottom—it is sucking to the bottom of the bilge area, and you do get dirt and dust. The dry bilge system gets all that into a centralizing area, and it might get clogged.

Five minutes, quick air-clean—it’s done. That’s amazing, right? That’ll also help save our bilge pumps in the future, without getting all that dirt in our bilge pumps and having to replace bilge pumps. That Arid Bilge—you’ve pulled it in there to a central location, you’re cleaning it out—your service guys are very happy about that.

Alfred: Dalton, thank you so much for your time. This has been an amazing experience on this boat. I love all your boats, to tell you the truth. 

Dalton: I hope that we’ve educated all boaters that it is important to have a dry bilge. A dry bilge is a happy bilge.

 

Why builders choose Arid: explore the benefits for builders and owners, and read our boat-building story.

21 04, 2024
  • boat builders discuss bilge system

Bahama Boat Works on Dry Bilges and Attention to Detail

By |2026-10-13T17:00:26+00:00April 21, 2024|Articles, Blog, Boat Builders, Boat Stories, Center Consoles|

Arid supplies Bahama Boat Works. The connection is easy to understand when you listen to Bob Sparks, Derek Rawnsley and Connor Henley: their discussion of a finished boat continues beneath the hatches. The bilge belongs in the same conversation as the visible joinery, electronics and deck hardware.

In our Bahama interview, Sparks and Rawnsley focus on what an owner sees when opening that space. Henley takes the discussion further, explaining why he recommended Arid to customers as part of caring for equipment below deck. Their comments give a useful starting point for buyers who want to understand the systems behind a well-presented boat.

The details a boat owner eventually has to reach

Founded by Scott Henley, Bahama builds offshore center consoles in Fort Pierce, Florida. Its current account of its design approach emphasizes positioning components for inspection, service and replacement. That practical detail matters long after the first walk-through.

When discussing a build, ask to see the equipment spaces as well as the finished cockpit. Where can water remain? Can the low areas be inspected without dismantling unrelated equipment? How will someone reach the drying system and its pickups for routine care? These questions make the below-deck specification concrete.

What Arid contributes

Arid collects residual water through pickups connected to a central unit. It serves the low areas included in that installation, alongside the boat’s conventional bilge pumps. Our explanation of how Arid works follows that route.

The distinction helps keep the equipment discussion useful. Removing standing water is one task; cleaning accumulated residue, maintaining connections and repairing a leak are others. A tidy-looking bilge still needs those checks. Ask the builder to explain the proposed coverage and access arrangements for your particular boat.

Fit the equipment to the owner’s boat

In the interview, Henley describes working with owners on equipment choices. That is a good reason to bring bilge drying into the build conversation early: discuss it alongside the systems sharing those compartments, rather than treating it as an isolated accessory.

For another view of access around installed equipment, read Dalton Teeter’s discussion aboard HCB’s Estrella. The Everglades 395 interview adds a captain’s account of an extended trip. Each describes its own boat and installation; the shared question is how the bilge will be inspected and cared for throughout ownership.

Prefer a quick introduction? Watch the existing Bahama interview Short.

Edited highlights from Bahama Boat Works

The following summary brings together the main points from the video. Watch the complete conversation above for the speakers’ own words.

Fit and finish continues below deck

Sparks and Rawnsley describe the bilge as part of the finished boat an owner sees. Opening a hatch should reveal a space that reflects the care taken elsewhere aboard. Their comments connect Arid’s residual-water collection with that expectation of a neat, clean compartment.

The equipment sharing the space matters, too. They discuss the electronics and other components installed below deck, and why the condition of the surrounding bilge deserves attention.

How Bahama Boat Works handles owner choices

Henley places that discussion in the context of Bahama’s approach to building boats. He describes a family-owned business with limited production and an emphasis on fit and finish. He also talks about the practical knowledge involved in working inside a boat’s equipment compartments.

In the discussion of component choices, he explains that Bahama has preferences while also working with customers on their requirements. Electronics and other onboard systems are part of that conversation. The point is to consider how the finished boat will be used and cared for, alongside the equipment specified during the build.

Consider the space around the equipment

Henley recommends Arid in the context of moisture that can collect in enclosed bilge areas. His examples include the combination of water, heat and closed hatches in a marine environment. The concern is the condition an owner finds when that space is opened again.

That makes bilge care part of the equipment discussion. Residual-water collection, access for inspection and continued maintenance all belong in the plan. The interview describes Bahama’s perspective and experience; the appropriate installation still depends on the individual boat.

Read more about Bahama Boat Works on their website.

See the water-routing animation

Illustrative Arid water-routing animation. Actual equipment placement and pickup locations vary by vessel and installation.

This silent animation shows pickups in separate low areas connected by tubing to a central Arid unit, with collected water moving through a discharge line.

Why builders choose Arid: explore the benefits for builders and owners, and read our boat-building story.