The Do’s And Don’ts Of Treating Bilge Water

Most of us boaters have to deal with bilge water on a daily basis. There is no question that thinking about it is just as much of a daunting process as dealing with it, though unfortunately, leaving it alone can have far worse consequences. Follow along to understand the do’s and dont’s of treating bilge water.

We’re going to be honest, your boat is often referred to as a vessel, and there is no way to completely avoid getting bilge water down below. It’s just a part of boating life. Of course, what matters most is how you decide to deal with it.

Bilge water can get into the hard-to-reach, lower compartments that sit at the bottom of your boat, leaving you with expensive and labor-intensive consequences in the long run, if not taken care of. Having good bilge pumps can minimize the amount of bilge water that your vessel carries around. But to keep your boat in pristine condition 100% of the time requires a lot of labor, or an Arid Bilge System. Keeping your bilges dry can also help to keep your vessel free from possible failure, while keeping your family, guests and crew safe.

If you’re sick of dealing with the negative consequences of bilge water or the labor intensive wet shop vac, we highly recommend picking up an Arid Bilge System. Simply use our dry bilge vacuum system, and there will be no need to further concern yourself about pesky bilge water. The bilges will remain dusty dry automatically.

It is as easy as installing the Arid Bilge System and leaving it running. It then picks up all of the bilge water before it becomes nasty, keeping your boat’s bilges 100% bone dry. Let’s dive into the do’s and don’ts of treating bilge water, so that you can get a better idea of why an Arid Bilge System might be your best option.

The Do’s And Don’ts

DO make sure to keep your bilge clean as often as you possibly can. A dirty bilge can lead to a whole mess of problems, including rust, corrosion, odor, humidity, mold growth, and more. These problems can lead to a smelly and uncomfortable boat. They can even eat away at the electrical, bonding and electronics systems. These sorts of damages can easily cost you thousands of dollars in repairs.

DON’T continue using temporary “solutions” to clean out your bilge. Many people rely on temporary fixes such as ozone machines which cause other issues, the wet vac which is very labor intensive and bilge cleaners which end up polluting the surrounding waters. All these “solutions” merely put a Band-Aid on the problem. You’ll still have to continuously stress about your bilge water and make sure that you are taking care of it all the time.

DO install a dry bilge vacuum system. Of course, the Arid Bilge System is the only multi-compartment system on the market. It slowly and efficiently vacuums liquids across a range of up to 75 feet from the central unit, keeping all your bilge compartments 100% dusty dry.

DON’T waste your time adding additional pumps. Arid Bilge is a high-quality and functional bilge vacuum system. It is the only system on the market that is proven to keep bilges 100% dry. It doesn’t make sense to go with any of the other companies pumps, when you could be getting the best of the best for a price that doesn’t break the bank.

Why Go With Arid Bilge System

We could think of a long list of reasons as to why you should purchase the Arid Bilge System over the companies that sell just pumps, though we’d have to write you an entire article just for that. The proof is in the vacuuming.

Do Install an Oily Water Separator if you can’t legally discharge overboard without one. Once you have an Arid Bilge System installed, we also offer the Eco Friendly Discharge Companion which is a permanently installed oily water separator. The Eco Friendly will retain the oil-found in many bilges. It holds the oil and fuel inside the separator, passing treated hydrocarbon-free water through, which is then normally discharged overboard. The three different Eco Friendly Discharge Companion models can also be fitted with any one of three different alarm systems, to let you know that oil or fuel is accumulating in the separator. Now, you are often able to identify that there is a developing oil or fuel leak, long before there is a big mess down below. Once there is a big mess down below, you often end up hiring a local company to show up with expensive equipment for the clean-up, and then you still have to locate and fix the leak that caused the big mess in the first place. With the Arid Bilge – Eco Friendly combination on board, you have dry bilges with small trails leading off the the source of a developing leak. Often it may be as easy as changing a hose or fitting, after the alarm had gone off, long before the big mess occurs. So it’s not just about avoiding the high fines, but the main caveat is the preventing of a big mess, and saving your equipment.

It should now be an obvious conclusion, to go with the Arid Bilge System. We have a top-notch line of products for all kinds of boats that work to help keep your bilges dry and oil free so that you can enjoy your boat the way you want to. Our superior marine bilge systems are the best products to help keep your boat clean and healthy for many years to come. Simply install our system and leave it to do its work automatically keeping the bilges clean and bone dry.

We wish you a happy and dry boating experience for years to come!

Sucking Water Out of the Bilge – How Does the Arid Bilge System Work

Since the invention of the floating vessel in ancient times, boaters have been dealing with stinky bilge water down below in their boats. It is most likely a fact that every boat which you rode on as a kid, had some of this ugly water sloshing around in the hard-to-reach bilge compartments down below. Common statements to deal with this reality would have been…

“It is what it is”  or

“This is just how it is. Get over it.”

Then, we invented the Arid Bilge System to change all of this . . . permanently. Today, boaters can enjoy a vessel that is  fresh and dry down below at all times! And without all the chores normally associated with this.

Bilge pump basics . . .

Before we dive in to find out how the Arid Bilge System works, let’s get on the same page and have a general understanding as to how bilge pumps work. Like their name says: bilge pumps, do pump water. This means that the water is pushed or propelled by an impeller of some type, be it a rubber lobe, centrifugal or similar. Most bilge pumps are generally high volume. Good seamanship skills would demand that you have enough pump(s) on board to prevent the vessel from sinking, in the event of a catastrophic type event, like a broken hose or a hole in the hull for instance. Bilge pumps are usually turned on automatically by a float switch, which won’t trigger until there is well over an inch of water down below. And boaters are usually frustrated when they hit the manual override switch, not being able to get rid of the rest of the bilge water – for two very good reasons: First, as air hits that impeller, the pump’s efficiency goes to zero, as the pump is not designed to move air with water. And secondly, as the pump shuts down, the water that’s in the discharge hose comes rushing back through the pump, returning into the bilge.

What is the Arid Bilge System?

Compared with bilge pumps, the Arid Bilge System works very much like a common shop or wet vac. All Arid Bilge Systems have miniature collection chambers similar the bucket on the wet vac. Air is vacuumed out of the collection chamber, and then bilge water rushes in to fill this void.  There is no priming necessary, all the water moves in one direction only. Then the water is trapped in the collection chamber. Now instead of relying on the  common float switch, the Arid System utilizes vacuum switches that keep these systems running, until air is pulled through the intake tubes, leaving the bilges bone dry and the intake tubes stripped of liquids. These systems are low volume, and are well tuned to the day-to-day needs of the average boat.

Essentially, the aging process of the interior of the boat does slow and nearly stops. Instead of dealing with the odor, condensation damage, mildew, corrosion, or rust, the Arid Bilge will suck up all of the residual water from the source so that you don’t have to deal with the problems caused by standing residual bilge water.

Common, old school solutions . . .

Before the Arid Bilge System, boaters were resorting to pouring bilge cleaners, in order to minimize odors. Yes, wet vacs, ozone machines, dehumidifiers, bilge diapers were all available to provide a partial solution to these common age old problems of the chronically wet bilge. These “solutions” do tend to act as a Band-Aid and work only as long as they are constantly being re-applied. But once the Arid Bilge System is installed, it becomes a game changer which so completely removes all of the standing bilge water, that you can now completely abandon the “Band-Aid solutions”.

See the Arid Bilge System in action below!

Why Buy an Arid Bilge System?

You can think of the Arid Bilge System as the maintenance worker that you thought you’d never have. It is a truly magical system that acts automatically, removing moisture, preventing mildew, and odor at the source. All while slowing the aging process, which helps to keep your boat free from rotting, corrosion, rust and condensation damage! As an added caveat, the Arid Bilge will also help you find small leaks, which will leave a wet trail through the dry bilge back to the source!

We hope that we’ve inspired you to raise the bar for a better boating experience for yourself with a brand new Arid Bilge System on board!