bilge water

13 11, 2025

The Future of Bilge Maintenance: Meet Arid Bilge Systems at Tuppen’s Marine

By Alfred Baurley|2026-01-18T22:20:07+00:00November 13, 2025|Articles|

Meet Arid Bilge Systems at Tuppen’s Marine

How It All Started

At the Miami International Boat Show, something innovative caught the attention of serious boaters, captains, and service professionals alike: Arid Bilge Systems. Designed to completely eliminate standing water from the bilge — not just reduce it — this technology is quickly becoming one of the most talked-about upgrades in the marine world.

Tuppen’s Marine saw this firsthand and knew it needed to be part of their in-store offerings. That’s why they partnered with Arid Bilge Systems to bring this breakthrough technology into their front showroom — giving South Florida boaters direct access to the dry bilge revolution.

What Is Arid Bilge Systems?

Arid Bilge Systems is the Dry Bilge Machine — a fully automatic, vacuum-powered solution that removes hidden water from the deepest, hardest-to-reach pockets inside your boat — from bow to stern. Unlike traditional bilge pumps, it doesn’t wait for inches of water to accumulate. Instead, it keeps the bilge Bone Dry at all times by cycling every few hours, pulling moisture from multiple zones and sending it to a central discharge point.

Whether you’re dealing with saltwater spray, melted ice, rainwater, or leftover cleaning fluids, Arid Bilge prevents corrosion, mildew, electrical failure, and the musty odors that every boater dreads.

Why Every Boat Needs One

Leaving water in the bilge isn’t just inconvenient — it causes long-term damage. Moisture accelerates rust, mold, and wiring corrosion, leading to expensive repairs. When the sun beats down on the back deck, it causes an intensely humid, corrosive environment that ages everything in the boat prematurely.

The Arid Bilge System is the only solution that proactively dries the bilge 24/7 with zero user input, protecting your investment and extending the life of your vessel. This technology is necessary for every boat — period.

Our Connection with Tuppen’s Marine

We first met the Tuppen’s Marine team at the Miami Boat Show, and the alignment was instant. Known for outfitting South Florida’s top fishermen and boaters, Tuppen’s Marine is a trusted destination for premium gear, local service, and expert advice.

We partnered up to produce a Tuppen’s Marine commercial, and their front showroom now features a dedicated Arid Bilge Systems display. Right next to the Series 1 and Series 2 units, you’ll find a looping video showcasing the product in action — along with testimonials and endorsements from some of the most respected names in the industry.

Don’t Just Take Our Word for It — Hear from the Builders

Installed by over 100 boat builders and counting, Arid Bilge Systems is endorsed by the very people who build the boats themselves. In our in-store video at Tuppen’s, you’ll see testimonials from:

These builders know firsthand how vital it is to keep bilges bone-dry — and why every boat rolling out of the yard should have this system onboard.

Visit Tuppen’s Today to Learn More

Whether you’re outfitting a brand-new center console or upgrading your current setup, stop by Tuppen’s Marine to see Arid Bilge Systems up close and experience the technology that’s raising the standard for boating cleanliness and protection.

Arid Bilge Systems – Dry. Fresh. Protected.

Watch the full video NOW!

13 03, 2024

Bilge System Installation: The Preparation Guide

By Al|2026-01-18T22:26:52+00:00March 13, 2024|Blog|

How To Prepare Your Boat Before Installing Your Dry Bilge System

Bilge System Installation If you want to keep your boat in pristine condition and prolong its life, it is more than necessary to have an effective dry bilge system installed. If you’ve noticed that your dirty old bilge pump hasn’t been pumping out water as effectively as it should, it is time to look into getting a new bilge vacuum system. Of course, we recommend that you look into our Arid Bilge System, as it is the best of the best! Plus, you can install it yourself. Installing an Arid Bilge System on your boat is relatively simple, usually not requiring the services of a skilled technician! Here is a simple step-by-step guide to prepare for your bilge system installation.

Pre-Installation

Before you begin installing your bilge system, we recommend a few steps to save yourself money and complete the job quickly and efficiently.

1. Determine How Many Zones or Distinct Wet Locations are on Your Boat

Start by assuring that your boat is in its natural static float position. In other words: if it’s up on the hard or with an engine removed it’s going to be a little hard to determine where and how the water pockets around the boat, compared to when it’s sitting at anchor or at the dock and in normal use. Next, bring a common wet vac on board. Take the hose and hold it in the deepest, lowest elevated location, then wait and relax. Water will often travel, slowly, through limber holes from other compartments nearby. Once the water stops flowing and that lowest, deepest, compartment is dried down to a sheen, then you are ready to move to the second lowest, deepest compartment, if there is one. You repeat this process until you come up with a zone count. Make sure that you don’t make the mistake of skipping compartments that don’t have traditional bilge pumps. Also, don’t expect that the existing, factory installed bilge pumps are even at the lowest deepest points in the first place.

2. Determine a Good Mounting Location for the Central Unit

In most boats we would recommend looking around in the engine room first, as it usually pockets the most water and is centrally located in the boat. Outboard boats like larger center consoles will generally have an aft compartment under the floor, hopefully with a large access hatch. You generally try to mount the system as high as possible. Placing the Arid Bilge System near the bottom of the bilge is a no no, as the central units are not water proof. The unit must be mounted upright, because: like the wet shop vac, it does have a collection bucket or chamber that has to fill with the collected bilge water, temporarily, before sending it overboard.

3. Determine Where the Discharge Water Will go

Next, we look for hoses that go to thru hull fittings, and determine if any are used for the occasional discharging of water. Air conditioning cooling water discharges are not recommended, as they can be pumping water overboard, continuously, most of the time. Hoses that are connected to deck, hatch or vent drains, as well as sink drains are usually preferred. We are looking to T connect our Arid Bilge discharge to an existing outflow, as this is usually much easier than drilling another hole in the side of the boat. We try to locate the unit above this discharge hose, so that the water leaving the Arid Bilge System travels downhill to flow overboard more completely. Then, we look for a power source. The Arid Bilge System can usually be connected to 12 or 24 volt DC or 120 volt AC house power. The Arid Bilge draws very little power and often ends up taking power from an existing bilge pump circuit as a matter of convenience. The ideal mounting location will be in close proximity to discharge and power offering enough space to mount the unit upright. Sometimes, this ends up being under the galley or head sink. Next, we have to make sure that the unit that we need, will fit in the available space. Modern boats are often crammed full with all kinds of pumps, systems, battery chargers, electronics etc. So, occasionally you may have to buy a three zone Series 2 instead of a four zone Series 4, just because there is no room for the larger system aboard.

4. Determine the Correct Bilge Pickup Type Needed for each Compartment

Bilge compartments come in all shapes and sizes. Remember when you held the wet vac hose in place waiting for the water to drain to each of the low points? If the bottom of the compartment was flat – then select the Standard or Mini Standard pickups. If the compartment came to a V at the bottom, then you would select the offset or pickup wand. We do provide a spare for every two zones, so you can often have it both ways when ordering.

Should You Buy An Arid Bilge System?

There are just about a hundred reasons to get an Arid Bilge System. Unlike regular bilge pumps or temporary solutions like bilge cleaners and ozone machines, the Arid Bilge System vacuums slowly and effectively to make sure that your boat remains 100% dusty dry at all times. This will keep the boat young and protect your investment from nasty odors and the damaging effects of rust and corrosion.

When you buy an Arid Bilge System, you are effectively prolonging the life of your boat and enhancing the resale value. If you’re ready to take the plunge check out our shop today. We’re ready to provide you with the best bilge products on the market! Happy boating!

6 03, 2024

A Guide To Boat Bilge Pumps

By Al|2026-01-18T22:27:18+00:00March 6, 2024|Blog|

A Guide To Boat Bilge Pumps – What Are They And How They Work

The unsettling thing about bilge pumps is the fact that they are usually a boat’s only line of defense before sinking into the deep blue, yet most boaters don’t know much about them. Rarely do boaters even talk about boat bilge pumps, and even less of their time is spent going down below to maintain them.

Of course, it is important that you get to know more about your boat bilge pumps, as you don’t want to end up being the proverbial old sailor, frantically taking water out of the bottom of his boat with a bucket.

Let’s dive in and take a deeper look into bilge pumps, what they are, what they do, and how to pick the best one.

What Are Bilge Pumps?

The job of a bilge pump is to clear the unwanted water that gets into the bilge on your boat. This water can come in due to errant waves, drip through packing gland, a broken hose or clamp, leaking port holes or hatches, and much more. Essentially, bilge water is almost impossible to avoid. While the stock bilge pump that came with your boat may do the job well, though, you want to be sure that it acts as a serious line of defense in the case that your boat begins sinking out at sea, giving you enough time to call for help or make it back to the marina.

Most well-educated captains who plan to undertake long crossings over open water will upgrade their bilge pumps by adding a higher-volume one, as a backup.

How Do They Work?

There are three common types of electrical bilge pumps that you will find on the market, namely the centrifugal, the rubber lobe and the diaphragm.

Centrifugal pumps work using a rotating, solid impeller, which like a turbine will push water. This type of pump will propel water up into the discharge hose and usually sits in the lowest, deepest position of the bilge. That water is pumped from the bottom up, but once air comes in contact with the impeller, cavitation usually stops the movement of water completely. Once this type of pump shuts down, all of the water that is still sitting in the discharge hose comes gushing backwards into the bilge. So the base water line left behind, when these pumps shut down, is usually around 1 ½”. The twin seals between the impeller and the motor, protect the pump’s electric motor sitting in the bilge, for a time, limiting the life of the pump. Many boaters have tried to place a check valve on the output side, near these pumps in order to prevent the back wash, only to find that this creates a condition called vapor lock, where the pump can’t prime itself, as air becomes trapped between the pump and the check valve. These are still the most popular of all bilge pumps as they are very quiet, use little power for the volume of water pumped, are relatively inexpensive and usually have a 3 to a 4 year life span in the average wet bilge. Also, if these pumps are accidentally left on, there is usually little damage potential within the first few hours.

Rubber lobe bilge pumps used to be the most popular and common of all bilge pumps, until Clinton Rule invented the Centrifugal bilge pump back in the early 60’s. These pumps have a rubber impeller that spins in a housing where there is a restriction between the intake and outflow, causing the rubber lobes to crush temporarily, attempting to compress the water and forcing it out into the discharge port. These pumps are lower volume and not particularly electrically efficient. They can pull some air with the water, but cannot be left to run dry under any circumstances. Here, the water lubricates the rubber impeller as it spins in the housing. So, without water, the impeller heats up and starts to stick to the housing. Additionally, if oil or fuel ends up being pulled through the impeller, the rubber will usually expand, also locking the pump. They will offer you a brown Nitrile replacement impeller that should not absorb the oil, and then you ask yourself, why didn’t they automatically install the Nitrile one at the factory. Most of the engines on boats today use a mechanically driven rubber lobe pump for their raw water engine cooling systems.

Diaphragm pumps have chambers, and work more like your heart, where they pulse to move the water through the two chambers and two one-way valves. So, this type of pump creates a suction that pulls out the unwanted bilge water. Diaphragm pumps can be run dry for a time without any damage, and are self-priming. This means that they develop suction and prime themselves without being submerged in water. Unfortunately, they cannot move as much water when compared to centrifugal pumps, and won’t be able to tolerate bits of debris or trash, which can lodge in the pump valves. These pumps will usually have an intake strainer that will fill with small debris and will have to be serviced / cleaned regularly. These pumps are the noisiest of all the pumps and again, these pumps are not as electrically efficient as the centrifugal pumps, but when set up correctly, they can draw the bilge water levels down to ½” in the manual mode. In the auto mode, when they are connected to the average float switch, they will usually still leave over an inch of water behind.

In simple terms, all bilge pumps leave residual bilge water behind and this is what brings us to the Arid Bilge System

The dry bilge system > The Arid Bilge System

For those who are in the market for the best of the best, we recommend the Arid Bilge System. The Arid Bilge System works uniquely as an automated computerized vacuum system, vacuuming up water from the bow to the mid to the stern of your vessel, through small tubing, up to 75 feet away from the central unit. Because it’s an automated system, you never have to think about going down to turn it on manually.

The Arid Bilge System utilizes air sensors/vacuum switches to make sure that the system knows when it is suctioning water vs air. It can be left to run dry forever… with no chance of damage to the internal air compressor. In fact, it does not pump water and there is no contact between the bilge water and any electrical component anywhere in the system. This means that there is no seal to fail, so you can expect excellent longevity from your new Arid Bilge System. The Arid Bilge System vacuums the bilge water into a small collection chamber inside the central unit, and then uses air pressure to push the collected water out through a check valve.

As an added safety feature we offer the Eco Friendly Discharge Companion/oily water separator which captures and stores oil that’s common in small amounts in many bilges. And an additional alarm is available to audibly notify you as oil starts to accumulate in the separator. With this system added to your Arid Bilge System, you can confidentially say that this oil slick surrounding your boat came from someone else’s boat.

You can see how the Arid Bilge System works with the little visual representation below:

Getting the Best Bilge System

Having a solid dry bilge system on your boat can create a happier and safer boating experience for you and the family. Don’t rely on old stock bilge pumps to keep you safe. Get yourself one of the best dry bilge systems around at Arid Bilge Systems!

28 02, 2024

The Do’s and Don’ts of Treating Bilge Water

By Al|2026-01-18T22:27:57+00:00February 28, 2024|Blog|

The Do’s And Don’ts Of Treating Bilge Water

Most of us boaters have to deal with bilge water on a daily basis. There is no question that thinking about it is just as much of a daunting process as dealing with it, though unfortunately, leaving it alone can have far worse consequences. Follow along to understand the do’s and dont’s of treating bilge water.

We’re going to be honest, your boat is often referred to as a vessel, and there is no way to completely avoid getting bilge water down below. It’s just a part of boating life. Of course, what matters most is how you decide to deal with it.

Bilge water can get into the hard-to-reach, lower compartments that sit at the bottom of your boat, leaving you with expensive and labor-intensive consequences in the long run, if not taken care of. Having good bilge pumps can minimize the amount of bilge water that your vessel carries around. But to keep your boat in pristine condition 100% of the time requires a lot of labor, or an Arid Bilge System. Keeping your bilges dry can also help to keep your vessel free from possible failure, while keeping your family, guests and crew safe.

If you’re sick of dealing with the negative consequences of bilge water or the labor intensive wet shop vac, we highly recommend picking up an Arid Bilge System. Simply use our dry bilge vacuum system, and there will be no need to further concern yourself about pesky bilge water. The bilges will remain dusty dry automatically.

It is as easy as installing the Arid Bilge System and leaving it running. It then picks up all of the bilge water before it becomes nasty, keeping your boat’s bilges 100% bone dry. Let’s dive into the do’s and don’ts of treating bilge water, so that you can get a better idea of why an Arid Bilge System might be your best option.

The Do’s And Don’ts

DO make sure to keep your bilge clean as often as you possibly can. A dirty bilge can lead to a whole mess of problems, including rust, corrosion, odor, humidity, mold growth, and more. These problems can lead to a smelly and uncomfortable boat. They can even eat away at the electrical, bonding and electronics systems. These sorts of damages can easily cost you thousands of dollars in repairs.

DON’T continue using temporary “solutions” to clean out your bilge. Many people rely on temporary fixes such as ozone machines which cause other issues, the wet vac which is very labor intensive and bilge cleaners which end up polluting the surrounding waters. All these “solutions” merely put a Band-Aid on the problem. You’ll still have to continuously stress about your bilge water and make sure that you are taking care of it all the time.

DO install a dry bilge vacuum system. Of course, the Arid Bilge System is the only multi-compartment system on the market. It slowly and efficiently vacuums liquids across a range of up to 75 feet from the central unit, keeping all your bilge compartments 100% dusty dry.

DON’T waste your time adding additional pumps. Arid Bilge is a high-quality and functional bilge vacuum system. It is the only system on the market that is proven to keep bilges 100% dry. It doesn’t make sense to go with any of the other companies pumps, when you could be getting the best of the best for a price that doesn’t break the bank.

Why Go With Arid Bilge System

We could think of a long list of reasons as to why you should purchase the Arid Bilge System over the companies that sell just pumps, though we’d have to write you an entire article just for that. The proof is in the vacuuming.

Do Install an Oily Water Separator if you can’t legally discharge overboard without one. Once you have an Arid Bilge System installed, we also offer the Eco Friendly Discharge Companion which is a permanently installed oily water separator. The Eco Friendly will retain the oil-found in many bilges. It holds the oil and fuel inside the separator, passing treated hydrocarbon-free water through, which is then normally discharged overboard. The three different Eco Friendly Discharge Companion models can also be fitted with any one of three different alarm systems, to let you know that oil or fuel is accumulating in the separator. Now, you are often able to identify that there is a developing oil or fuel leak, long before there is a big mess down below. Once there is a big mess down below, you often end up hiring a local company to show up with expensive equipment for the clean-up, and then you still have to locate and fix the leak that caused the big mess in the first place. With the Arid Bilge – Eco Friendly combination on board, you have dry bilges with small trails leading off the the source of a developing leak. Often it may be as easy as changing a hose or fitting, after the alarm had gone off, long before the big mess occurs. So it’s not just about avoiding the high fines, but the main caveat is the preventing of a big mess, and saving your equipment.

It should now be an obvious conclusion, to go with the Arid Bilge System. We have a top-notch line of products for all kinds of boats that work to help keep your bilges dry and oil free so that you can enjoy your boat the way you want to. Our superior marine bilge systems are the best products to help keep your boat clean and healthy for many years to come. Simply install our system and leave it to do its work automatically keeping the bilges clean and bone dry.

We wish you a happy and dry boating experience for years to come!

14 02, 2024

How Does the Arid Bilge System Work?

By Al|2026-01-18T22:28:31+00:00February 14, 2024|Blog|

Sucking Water Out of the Bilge – How Does the Arid Bilge System Work

Since the invention of the floating vessel in ancient times, boaters have been dealing with stinky bilge water down below in their boats. It is most likely a fact that every boat which you rode on as a kid, had some of this ugly water sloshing around in the hard-to-reach bilge compartments down below. Common statements to deal with this reality would have been…

“It is what it is” or

“This is just how it is. Get over it.”

Then, we invented the Arid Bilge System to change all of this . . . permanently. Today, boaters can enjoy a vessel that is fresh and dry down below at all times! And without all the chores normally associated with this.

Bilge pump basics . . .

Before we dive in to find out how the Arid Bilge System works, let’s get on the same page and have a general understanding as to how bilge pumps work. Like their name says: bilge pumps, do pump water. This means that the water is pushed or propelled by an impeller of some type, be it a rubber lobe, centrifugal or similar. Most bilge pumps are generally high volume. Good seamanship skills would demand that you have enough pump(s) on board to prevent the vessel from sinking, in the event of a catastrophic type event, like a broken hose or a hole in the hull for instance. Bilge pumps are usually turned on automatically by a float switch, which won’t trigger until there is well over an inch of water down below. And boaters are usually frustrated when they hit the manual override switch, not being able to get rid of the rest of the bilge water – for two very good reasons: First, as air hits that impeller, the pump’s efficiency goes to zero, as the pump is not designed to move air with water. And secondly, as the pump shuts down, the water that’s in the discharge hose comes rushing back through the pump, returning into the bilge.

What is the Arid Bilge System?

Compared with bilge pumps, the Arid Bilge System works very much like a common shop or wet vac. All Arid Bilge Systems have miniature collection chambers similar the bucket on the wet vac. Air is vacuumed out of the collection chamber, and then bilge water rushes in to fill this void. There is no priming necessary, all the water moves in one direction only. Then the water is trapped in the collection chamber. Now instead of relying on the common float switch, the Arid System utilizes vacuum switches that keep these systems running, until air is pulled through the intake tubes, leaving the bilges bone dry and the intake tubes stripped of liquids. These systems are low volume, and are well tuned to the day-to-day needs of the average boat.

Essentially, the aging process of the interior of the boat does slow and nearly stops. Instead of dealing with the odor, condensation damage, mildew, corrosion, or rust, the Arid Bilge will suck up all of the residual water from the source so that you don’t have to deal with the problems caused by standing residual bilge water.

Common, old school solutions . . .

Before the Arid Bilge System, boaters were resorting to pouring bilge cleaners, in order to minimize odors. Yes, wet vacs, ozone machines, dehumidifiers, bilge diapers were all available to provide a partial solution to these common age old problems of the chronically wet bilge. These “solutions” do tend to act as a Band-Aid and work only as long as they are constantly being re-applied. But once the Arid Bilge System is installed, it becomes a game changer which so completely removes all of the standing bilge water, that you can now completely abandon the “Band-Aid solutions”.

See the Arid Bilge System in action below!

Why Buy an Arid Bilge System?

You can think of the Arid Bilge System as the maintenance worker that you thought you’d never have. It is a truly magical system that acts automatically, removing moisture, preventing mildew, and odor at the source. All while slowing the aging process, which helps to keep your boat free from rotting, corrosion, rust and condensation damage! As an added caveat, the Arid Bilge will also help you find small leaks, which will leave a wet trail through the dry bilge back to the source!

We hope that we’ve inspired you to raise the bar for a better boating experience for yourself with a brand new Arid Bilge System on board!